From: How to Program A 5834-4 To A VISTA P Panel
The Honeywell 5834-4 key fob needs a 5881 series wireless receiver or anRF keypad connected to a Vista panel to communicate.
To program enter programming by entering the installer code (Honeywell factory default code is [4112] [800].
Press *58 to enter the summary screen.
Enter Template number 1 to 6 (3)
Press the star (*) key to display template. Top line of display represents loop numbers; bottom line represents zone type assigned for each loop (refer to the Vista programming guide for complete list of templates).
Press the star (*) key to accept.
Enter the partition the key fob is to be assigned to 1
Then press the star (*) key to continue.
The system will search for the highest available consecutive 4-zone group and display the lowest zone number of the group.
To start at a different zone, enter the zone desired Paul: 49, Betty: 51.
Press the star (*) key.
If the required number of consecutive zones is not available at all, the system will display "00".
Press the star (*) key to accept
Manually enter the 7 digit serial number printed on the label of the key fob or or press and release a button to transmit its serial number.
Press the star (*) key to accept the serial number. The system will check for a duplicate.
If the serial number transmitted does not match the serial number entered, a display similar to the one shown will appear.
If the loop number does not match, it will also be displayed. If it does not match re enter the serial number.
If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and will return to the
zone number prompt where another key fob can be entered. Confirm serial and loop numbers by activating the key fob.
Assign the key fob to a user number, it is not active for arming/disarming until it is assigned to a user number OR

---

From: How to program a four button key fob on a Honeywell Vista
Wireless keys are one of the hardest things to program on a Vista panel. Luckily they aren‘t too hard, but there is a few steps to it.
1 - Enter programming with your installer code followed by 800.
2 - Go to *58.
3 - When it says set to confirm select 1.
4 - At the summary screen you will want to press the ‘D‘ key. It is the bottom function key on the left side of the keypad.
5 - The screen should ask for a template. The most common one for the 5834-4 keyfob is template 3. For a full list you can check the programming guide.
6 - For 20P or 21iP, you have to select partition 1 or 2 and then press star (*).
7 - The system will automatically pick the lowest zone of the highest consecutive 4 zone set and display that on the screen. It is a good idea to write that zone number down so that you have it for easy reference later. Then press star (*).
8 - Here you can press and release a button to transmit the serial number for the wireless key or just enter it manually. Press star (*) when finished.
9 - Press a button on the remote to confirm that the serial and loop numbers match.
10 - You will then be shown the next available zone to add another key. If you are adding another key, repeat steps 7-9. Otherwise enter 00 to exit.
11 - You will be back at a zone summary screen at the beginning of the *58 menu. Enter 00 and press * to exit.
12 - Enter *99 to exit programming mode.


13 - Now you‘l need to associate each wireless key with a user code before they will function. To do this you‘ll enter the following string of numbers:
User numbers: 03 = Paul, 04 = Betty.
Master code [1234] [8 + user number] + #4 + zone number. 49,50,51,52
Zones: 49 = Paul, 51 = Betty.
The user number we‘ll use is 02.
And then you would use the zone number from step 7. For our example we’ll use 49.
So the full strings will be:
1234802#449 1234802#450 1234802#451 1234802#452
We recommend writing out what you’ll be using to make entering it much easier.
After entering the proper string of code you‘ll hear a ding from the keypad.