Shooters Choice (Bore cleaning)
There are so many good gun
cleaning products out there, that it is hard to be sure that you're using the "best" one. Shooters Choice is a
product that I recommend (and no, I don't sell it.) Most new shooters regard bore cleaning as a chore that
can be done later, if it even gets done at all. No one seems to enjoy taking the time to do this job, but
experienced shooters know the importance of cleaning their rifle barrels to maintain top accuracy. One
thing is for sure .... everyone seems to have developed their own preferred cleaning procedure. These magnified pictures
show what your bore looks like before and after
a good cleaning. The area photographed is about 4" ahead of the
chamber on an average hunting rifle. Without a borescope, all
you can see is a few copper streaks at the muzzle. If you
prevent this copper fowling from building up, your rifle will keep its
peak accuracy for a lot longer. Always finish up by leaving a
very light coat of Kroil in the barrel.
Cleaning the average hunting rifle is quite different from cleaning an expensive benchrest
rifle. I've found that there is no single method that is "the only way to do it". However, there are some
precautions to take and a few techniques that can make the job faster and easier. First .... if it is possible, it
is always best to clean a barrel from the rear, and you should use a use a rod guide to avoid doing more damage
than good.
I have no preference for stainless steel rods over
coated rods as long as they are absolutely clean, straight as an arrow
and free from nicks or dings. Avoid using jointed rods unless it
is the last resort and you're desperate. I prefer to use a patch
that is wrapped around an undersize bore brush, instead of using a jag.
This gives your patch a tight fit against the lands and grooves.
If you've ever used the wrong size patch on a jag and got your
cleaning rod stuck in your barrel, then you'll really like this method
because that will never happen to you again.
After firing no more than 20 rounds, I clean my
barrels by running a patch down the barrel with a good supply of
Shooters Choice on it. The material that I use for patches is a
strip of paper towel. At the risk of sounding like a TV
commercial, "Bounty" paper towels really is the best brand to use,
because they don't get soggy like other brands. After the bore
is wet, I run a bore brush completely through it (about 15 to 20
swipes) while keeping the bore wet. Notice the tight fit that
you have when using a new bore brush. When bore brushes start to
wear out, you will notice that they can be pushed through your barrel
with less resistance. Be sure to discard your bore brushes at
that point.
If you're cleaning a benchrest barrel never pull
the brush back from the muzzle. At all cost, you always need to
be careful to protect the crown of your barrel. Every now and
then, I add a few extra steps at the end of the cleaning process.
I wet down the inside of the barrel with Kroil, and I coat a
patch with JB Bore Paste. Then I use it to scrub the barrel
paying extra attention to the first few inches ahead of the chamber.
On this step, with the "paper towel on a brush" method, you can
run the patch both ways in the bore, but once it exits the muzzle -
remove the brush. Don't pull the brush back after it exits the
barrel. A close examination of a neglected barrel will show that
the bore diameter is often "reduced" by a build up of bullet copper and
extremely hard fowling just ahead of the throat. A close
examination of a "worn out" barrel shows the first few inches of
rifling looking very shallow.
If you have another method of cleaning .... that's perfectly OK.
Bore cleaning can be performed very well by using several different
cleaning products in a variety of ways. There are volumes of
information written on this subject. If you would like to try my
"paper towel" method, I clean .30 cal. barrels useing a .22 cal. brush
with a paper towel patch (slightly larger than a dollar bill) wrapped
around it. This method works for me. I can usually get
the job done in less time than it takes most shooters, and my bore
scope proves that this method works very well.
BEFORE
AFTER
Cleaning pistol barrels is similar to cleaning a rifle barrel except when you are shooting lead bullets. There are 2 tools that I use to remove leading. The popular Lewis Lead Remover does a great job. Another method is to use a worn bore brush that has copper mesh wrapped around it. You can get the copper mesh in any grocery store. This stuff is used to scrub pots and pans .... just be sure that it is made of copper. These two methods work best when a pistol barrel is bone dry. It really gets the lead out without damaging the bore. After you get the lead out, you can finish cleaning by using Shooters Choice on a brush. When the barrel is clean, just swab the it out with kroil, and wipe most of it off with a dry patch.
Cleaning shotgun barrels after a day of shooting skeet, trap or sporting clays, can take some time. The toughest part is removing the plastic wad residue and powder from the barrel(s). The first step is to coat the inside of your barrel(s) with a powder solvent. I use a special tool that I made from a power screwdriver. It slowly spins the cleaning rod while you run a wet bore brush down the barrel and back. I wrap a small "Bounty" paper towel patch around the brush, so that it holds more cleaning fluid. I prefer to use a solvent called "Wads Out" made by Seminole Gunworks. Quite often, after 3 or 4 passes, it's just about done. Wipe it dry and inspect the barrel(s) to see if you need to repeat this process. When the barrel(s) are clean, just swab the barrel with kroil and wipe most of it off with a dry patch.
